Difference between revisions of "Reprap Prusa"
Jump to navigation
Jump to search
(Created page with "Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa") |
|||
Line 1: | Line 1: | ||
Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa | Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa | ||
+ | |||
+ | Build instructions: [[File:Prusa Mendel Visual Instructions (Mininum Resolution).pdf]] | ||
+ | |||
+ | BOM: -- | ||
+ | {| class="wikitable" | ||
+ | |+ Bill of Materials: Non-Printed Parts | ||
+ | ! Quantity | ||
+ | ! Description | ||
+ | ! Type | ||
+ | ! Comments | ||
+ | |+ | ||
+ | | 83 | ||
+ | | M8 nut | ||
+ | | Fastener | ||
+ | | Buy a 100-pack to be on the safe side. | ||
+ | |+ | ||
+ | | 93 | ||
+ | | M8 washer | ||
+ | | Fastener | ||
+ | | Buy a 100-pack to be on the safe side. | ||
+ | |+ | ||
+ | | 6 | ||
+ | | M8×30 mudguard / fender washers | ||
+ | | Fastener | ||
+ | | | ||
+ | |+ | ||
+ | | M4×20 bolt | ||
+ | | Fastener | ||
+ | | 2 | ||
+ | | | ||
+ | |+ | ||
+ | | M4 nut | ||
+ | | Fastener | ||
+ | | 2 | ||
+ | | | ||
+ | |+ | ||
+ | | M4 washer | ||
+ | | Fastener | ||
+ | | 22 | ||
+ | |+ | ||
+ | | M3×10 bolt | ||
+ | | Fastener | ||
+ | | 16 | ||
+ | |+ | ||
+ | | M3×25 bolt | ||
+ | | Fastener | ||
+ | | Or eight M3×25 bolt plus eight M3x20 bolts, see §8 steps 5 and 13 for details. | ||
+ | |+ | ||
+ | | 4 | ||
+ | | M3×40 bolt | ||
+ | | Fastener | ||
+ | |+ | ||
+ | | 70 | ||
+ | | M3 washer | ||
+ | | Fastener | ||
+ | |+ | ||
+ | | 40 | ||
+ | | M3 nut | ||
+ | | Fastener | ||
+ | | Eight optionally locknut / stop nut / nyloc | ||
+ | |+ | ||
+ | | 2 | ||
+ | | M3 grub screw / set screw | ||
+ | | Fastener | ||
+ | |+ | ||
+ | | 3 | ||
+ | | 608 roller skate / inline skate / skateboard bearing | ||
+ | | Bearings | ||
+ | |+ | ||
+ | | 4 | ||
+ | | ballpoint pen springs | ||
+ | | Spring | ||
+ | |+ | ||
+ | | 6 | ||
+ | | M8×370mm | ||
+ | | Threaded rod | ||
+ | | Three per side | ||
+ | |+ | ||
+ | | 4 | ||
+ | | M8×294mm | ||
+ | | Threaded rod | ||
+ | | Front / rear | ||
+ | |+ | ||
+ | | 3 | ||
+ | | M8×440mm | ||
+ | | Threaded rod | ||
+ | | Top / bottom | ||
+ | |+ | ||
+ | | 2 | ||
+ | | M8×210mm | ||
+ | | Threaded rod | ||
+ | | Z-leadscrew | ||
+ | |+ | ||
+ | | 1 | ||
+ | | M8×50mm | ||
+ | | Threaded rod | ||
+ | | Or bolt for X idler | ||
+ | |+ | ||
+ | | 2 | ||
+ | | 8mm×420mm | ||
+ | | Smooth rod | ||
+ | |+ | ||
+ | | 2 | ||
+ | | 8mm×406mm | ||
+ | | Smooth rod | ||
+ | | Y-bar | ||
+ | |+ | ||
+ | | 2 | ||
+ | | 8mm×350mm | ||
+ | | Smooth rod | ||
+ | | Z-bar | ||
+ | |+ | ||
+ | | 1 | ||
+ | | 225mm×225mm print top plate | ||
+ | | Thick Sheet | ||
+ | |+ | ||
+ | | 1 | ||
+ | | 140mm×225mm print bottom plate | ||
+ | | Thick Sheet | ||
+ | |+ | ||
+ | | 1 | ||
+ | | 840mm×5mm T5 pitch timing belt | ||
+ | | Belt | ||
+ | |+ | ||
+ | | 1 | ||
+ | | 1380mm×5mm T5 pitch timing belt | ||
+ | | Belt | ||
+ | |+ | ||
+ | | 5 | ||
+ | | NEMA 17 bipolar stepper motor | ||
+ | | Stepper | ||
+ | |+ | ||
+ | | 50 | ||
+ | | small cable binder / ziptie | ||
+ | | Misc | ||
+ | |+ | ||
+ | | 1 | ||
+ | | Wade's Geared Extruder | ||
+ | | | ||
+ | | Or any other compatible extruder | ||
+ | |+ | ||
+ | | 1 | ||
+ | | Electronics + endstops | ||
+ | | | ||
+ | | This can be RAMPS, Gen6, Gen3, or anything else compatible | ||
+ | |+ | ||
+ | | 3 | ||
+ | | 30mm×10mm Optoflags | ||
+ | | Thin Sheet | ||
+ | | If using opto endstops | ||
+ | |+ | ||
+ | | 2 | ||
+ | | 8mm ID spring | ||
+ | | Spring | ||
+ | | If using opto endstops | ||
+ | |} |
Revision as of 08:35, 23 May 2011
Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa
Build instructions: File:Prusa Mendel Visual Instructions (Mininum Resolution).pdf
BOM: --
Quantity | Description | Type | Comments |
---|---|---|---|
83 | M8 nut | Fastener | Buy a 100-pack to be on the safe side. |
93 | M8 washer | Fastener | Buy a 100-pack to be on the safe side. |
6 | M8×30 mudguard / fender washers | Fastener | |
M4×20 bolt | Fastener | 2 | |
M4 nut | Fastener | 2 | |
M4 washer | Fastener | 22 | |
M3×10 bolt | Fastener | 16 | |
M3×25 bolt | Fastener | Or eight M3×25 bolt plus eight M3x20 bolts, see §8 steps 5 and 13 for details. | |
4 | M3×40 bolt | Fastener | |
70 | M3 washer | Fastener | |
40 | M3 nut | Fastener | Eight optionally locknut / stop nut / nyloc |
2 | M3 grub screw / set screw | Fastener | |
3 | 608 roller skate / inline skate / skateboard bearing | Bearings | |
4 | ballpoint pen springs | Spring | |
6 | M8×370mm | Threaded rod | Three per side |
4 | M8×294mm | Threaded rod | Front / rear |
3 | M8×440mm | Threaded rod | Top / bottom |
2 | M8×210mm | Threaded rod | Z-leadscrew |
1 | M8×50mm | Threaded rod | Or bolt for X idler |
2 | 8mm×420mm | Smooth rod | |
2 | 8mm×406mm | Smooth rod | Y-bar |
2 | 8mm×350mm | Smooth rod | Z-bar |
1 | 225mm×225mm print top plate | Thick Sheet | |
1 | 140mm×225mm print bottom plate | Thick Sheet | |
1 | 840mm×5mm T5 pitch timing belt | Belt | |
1 | 1380mm×5mm T5 pitch timing belt | Belt | |
5 | NEMA 17 bipolar stepper motor | Stepper | |
50 | small cable binder / ziptie | Misc | |
1 | Wade's Geared Extruder | Or any other compatible extruder | |
1 | Electronics + endstops | This can be RAMPS, Gen6, Gen3, or anything else compatible | |
3 | 30mm×10mm Optoflags | Thin Sheet | If using opto endstops |
2 | 8mm ID spring | Spring | If using opto endstops |