Difference between revisions of "BarBot/Components/Makerslide and Platform"
Iandickinson (talk | contribs) |
Iandickinson (talk | contribs) |
||
| Line 13: | Line 13: | ||
Notes: | Notes: | ||
| − | * Not sure whether the ultrasonic sensor will be affected by spills and splashes | + | * Not sure whether the ultrasonic sensor will be affected by spills and splashes. |
* To prevent overheating of the Pololu driver and/or stepper motor, it is recommended that the stepper driver is disabled whenever the platform is stationary. (However, this does present a risk of not knowing the position if it should be knocked whilst disabled.) | * To prevent overheating of the Pololu driver and/or stepper motor, it is recommended that the stepper driver is disabled whenever the platform is stationary. (However, this does present a risk of not knowing the position if it should be knocked whilst disabled.) | ||
| Line 20: | Line 20: | ||
===Logical=== | ===Logical=== | ||
| − | The Pololu driver needs three | + | The Pololu driver needs three Arduino digital outputs: Enable, Step, Direction |
The ATtiny85 in the platform provides a "glass present" signal. (0 = no glass, 1 = glass present) | The ATtiny85 in the platform provides a "glass present" signal. (0 = no glass, 1 = glass present) | ||
| + | |||
| + | A further "mode" signal is used to select ultrasonic diagnostic mode (if low when power applied), or over-ride the ultrasonic sensor (if low during normal mode). | ||
===Connections=== | ===Connections=== | ||
| − | + | {| class="wikitable" | |
| − | + | |- | |
| − | + | ! Wire colour !! Signal | |
| − | + | |- | |
| + | | Black || Stepper coil A | ||
| + | |- | ||
| + | | Green || Stepper coil A | ||
| + | |- | ||
| + | | Blue || Stepper coil B | ||
| + | |- | ||
| + | | Red || Stepper coil B | ||
| + | |- | ||
| + | | Orange || +5V supply to ATtiny85 and Neopixel ring | ||
| + | |- | ||
| + | | Brown|| Ground | ||
| + | |- | ||
| + | | White || "Glass present" output | ||
| + | |- | ||
| + | | Yellow || Diagnostics / ultrasonic over-ride "mode" input | ||
| + | |} | ||
===Power=== | ===Power=== | ||
| − | +12V, TBC mA | + | * Stepper motor / Pololu driver: +12V, TBC mA |
| + | * ATtiny85 / Neopixel ring: +5V, TBC mA | ||
===Bling=== | ===Bling=== | ||
An awesome 24 RGB LED Neopixel ring! | An awesome 24 RGB LED Neopixel ring! | ||
Revision as of 23:11, 1 July 2014
Makerslide and platform
General Description
The 24 RGB Neopixel ring illuminated drinks platform glides along awesome Makerslide!
The platform is moved by a NEMA17 Stepper Motor, 1.8° per step, 1.7 A, 4000 g·cm stepper motor driven by a Pololu stepper driver. The AccelStepper library is used to control the stepper. One cm travel is approx 55 steps.
An ultrasonic sensor is used to detect the presence of a glass. This provides a signal to a local ATtiny85 in the platform, which in turn controls the Neopixel LEDs and provides a "glass present" signal to the master Arduino.
The left hand end of the Makerslide has a limit switch. This should be used to "zero" the stepper on each cycle.
Notes:
- Not sure whether the ultrasonic sensor will be affected by spills and splashes.
- To prevent overheating of the Pololu driver and/or stepper motor, it is recommended that the stepper driver is disabled whenever the platform is stationary. (However, this does present a risk of not knowing the position if it should be knocked whilst disabled.)
Mounting & hardware
T-slot nuts are used to invisibly (and very nicely) mount the Makerslide.
Logical
The Pololu driver needs three Arduino digital outputs: Enable, Step, Direction
The ATtiny85 in the platform provides a "glass present" signal. (0 = no glass, 1 = glass present)
A further "mode" signal is used to select ultrasonic diagnostic mode (if low when power applied), or over-ride the ultrasonic sensor (if low during normal mode).
Connections
| Wire colour | Signal |
|---|---|
| Black | Stepper coil A |
| Green | Stepper coil A |
| Blue | Stepper coil B |
| Red | Stepper coil B |
| Orange | +5V supply to ATtiny85 and Neopixel ring |
| Brown | Ground |
| White | "Glass present" output |
| Yellow | Diagnostics / ultrasonic over-ride "mode" input |
Power
- Stepper motor / Pololu driver: +12V, TBC mA
- ATtiny85 / Neopixel ring: +5V, TBC mA
Bling
An awesome 24 RGB LED Neopixel ring!