Difference between revisions of "Reprap Prusa"

From Nottinghack Wiki
Jump to navigation Jump to search
(Created page with "Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa")
 
Line 1: Line 1:
 
Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa
 
Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa
 +
 +
Build instructions: [[File:Prusa Mendel Visual Instructions (Mininum Resolution).pdf]]
 +
 +
BOM: --
 +
{| class="wikitable"
 +
|+ Bill of Materials: Non-Printed Parts
 +
! Quantity
 +
! Description
 +
! Type
 +
! Comments
 +
|+
 +
| 83
 +
| M8 nut
 +
| Fastener
 +
| Buy a 100-pack to be on the safe side.
 +
|+
 +
|  93
 +
| M8 washer
 +
| Fastener
 +
| Buy a 100-pack to be on the safe side.
 +
|+
 +
| 6
 +
| M8×30 mudguard / fender washers
 +
| Fastener
 +
|
 +
|+
 +
| M4×20 bolt
 +
| Fastener
 +
| 2
 +
|
 +
|+
 +
| M4 nut
 +
| Fastener
 +
| 2
 +
|
 +
|+
 +
| M4 washer
 +
| Fastener
 +
| 22
 +
|+
 +
| M3×10 bolt
 +
| Fastener
 +
| 16
 +
|+
 +
| M3×25 bolt
 +
| Fastener
 +
| Or eight M3×25 bolt plus eight M3x20 bolts, see §8 steps 5 and 13 for details.
 +
|+
 +
| 4
 +
| M3×40 bolt
 +
| Fastener
 +
|+
 +
| 70
 +
| M3 washer
 +
| Fastener
 +
|+
 +
| 40
 +
| M3 nut
 +
| Fastener
 +
| Eight optionally locknut / stop nut / nyloc
 +
|+
 +
| 2
 +
| M3 grub screw / set screw
 +
| Fastener
 +
|+
 +
| 3
 +
| 608 roller skate / inline skate / skateboard bearing
 +
| Bearings
 +
|+
 +
| 4
 +
| ballpoint pen springs
 +
| Spring
 +
|+
 +
| 6
 +
| M8×370mm
 +
| Threaded rod
 +
| Three per side
 +
|+
 +
| 4
 +
| M8×294mm
 +
| Threaded rod
 +
| Front / rear
 +
|+
 +
| 3
 +
| M8×440mm
 +
| Threaded rod
 +
| Top / bottom
 +
|+
 +
| 2
 +
| M8×210mm
 +
| Threaded rod
 +
| Z-leadscrew
 +
|+
 +
| 1
 +
| M8×50mm
 +
| Threaded rod
 +
| Or bolt for X idler
 +
|+
 +
| 2
 +
| 8mm×420mm
 +
| Smooth rod
 +
|+
 +
| 2
 +
| 8mm×406mm
 +
| Smooth rod
 +
| Y-bar
 +
|+
 +
| 2
 +
| 8mm×350mm
 +
| Smooth rod
 +
| Z-bar
 +
|+
 +
| 1
 +
| 225mm×225mm print top plate
 +
| Thick Sheet
 +
|+
 +
| 1
 +
| 140mm×225mm print bottom plate
 +
| Thick Sheet
 +
|+
 +
| 1
 +
| 840mm×5mm T5 pitch timing belt
 +
| Belt
 +
|+
 +
| 1
 +
| 1380mm×5mm T5 pitch timing belt
 +
| Belt
 +
|+
 +
| 5
 +
| NEMA 17 bipolar stepper motor
 +
| Stepper
 +
|+
 +
| 50
 +
| small cable binder / ziptie
 +
| Misc
 +
|+
 +
| 1
 +
| Wade's Geared Extruder
 +
|
 +
| Or any other compatible extruder
 +
|+
 +
| 1
 +
| Electronics + endstops
 +
|
 +
| This can be RAMPS, Gen6, Gen3, or anything else compatible
 +
|+
 +
| 3
 +
| 30mm×10mm Optoflags
 +
| Thin Sheet
 +
| If using opto endstops
 +
|+
 +
| 2
 +
| 8mm ID spring
 +
| Spring
 +
| If using opto endstops
 +
|}

Revision as of 08:35, 23 May 2011

Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa

Build instructions: File:Prusa Mendel Visual Instructions (Mininum Resolution).pdf

BOM: --

Bill of Materials: Non-Printed Parts
Quantity Description Type Comments
83 M8 nut Fastener Buy a 100-pack to be on the safe side.
93 M8 washer Fastener Buy a 100-pack to be on the safe side.
6 M8×30 mudguard / fender washers Fastener
M4×20 bolt Fastener 2
M4 nut Fastener 2
M4 washer Fastener 22
M3×10 bolt Fastener 16
M3×25 bolt Fastener Or eight M3×25 bolt plus eight M3x20 bolts, see §8 steps 5 and 13 for details.
4 M3×40 bolt Fastener
70 M3 washer Fastener
40 M3 nut Fastener Eight optionally locknut / stop nut / nyloc
2 M3 grub screw / set screw Fastener
3 608 roller skate / inline skate / skateboard bearing Bearings
4 ballpoint pen springs Spring
6 M8×370mm Threaded rod Three per side
4 M8×294mm Threaded rod Front / rear
3 M8×440mm Threaded rod Top / bottom
2 M8×210mm Threaded rod Z-leadscrew
1 M8×50mm Threaded rod Or bolt for X idler
2 8mm×420mm Smooth rod
2 8mm×406mm Smooth rod Y-bar
2 8mm×350mm Smooth rod Z-bar
1 225mm×225mm print top plate Thick Sheet
1 140mm×225mm print bottom plate Thick Sheet
1 840mm×5mm T5 pitch timing belt Belt
1 1380mm×5mm T5 pitch timing belt Belt
5 NEMA 17 bipolar stepper motor Stepper
50 small cable binder / ziptie Misc
1 Wade's Geared Extruder Or any other compatible extruder
1 Electronics + endstops This can be RAMPS, Gen6, Gen3, or anything else compatible
3 30mm×10mm Optoflags Thin Sheet If using opto endstops
2 8mm ID spring Spring If using opto endstops
Retrieved from "https://wiki.nottinghack.org.uk/index.php?title=Reprap_Prusa&oldid=1179"