Difference between revisions of "Reprap Prusa"
Jump to navigation
Jump to search
| Line 26: | Line 26: | ||
| | | | ||
|+ | |+ | ||
| + | | 2 | ||
| M4×20 bolt | | M4×20 bolt | ||
| Fastener | | Fastener | ||
| − | |||
| | | | ||
|+ | |+ | ||
| + | | 2 | ||
| M4 nut | | M4 nut | ||
| Fastener | | Fastener | ||
| − | |||
| | | | ||
|+ | |+ | ||
| + | | 2 | ||
| M4 washer | | M4 washer | ||
| Fastener | | Fastener | ||
| + | | | ||
| + | |+ | ||
| 22 | | 22 | ||
| − | |||
| M3×10 bolt | | M3×10 bolt | ||
| Fastener | | Fastener | ||
| + | | | ||
| + | |+ | ||
| 16 | | 16 | ||
| − | |||
| M3×25 bolt | | M3×25 bolt | ||
| Fastener | | Fastener | ||
| Line 51: | Line 54: | ||
| M3×40 bolt | | M3×40 bolt | ||
| Fastener | | Fastener | ||
| + | | | ||
|+ | |+ | ||
| 70 | | 70 | ||
| M3 washer | | M3 washer | ||
| Fastener | | Fastener | ||
| + | | | ||
|+ | |+ | ||
| 40 | | 40 | ||
| Line 64: | Line 69: | ||
| M3 grub screw / set screw | | M3 grub screw / set screw | ||
| Fastener | | Fastener | ||
| + | | | ||
|+ | |+ | ||
| 3 | | 3 | ||
| 608 roller skate / inline skate / skateboard bearing | | 608 roller skate / inline skate / skateboard bearing | ||
| Bearings | | Bearings | ||
| + | | | ||
|+ | |+ | ||
| 4 | | 4 | ||
| ballpoint pen springs | | ballpoint pen springs | ||
| Spring | | Spring | ||
| + | | | ||
|+ | |+ | ||
| 6 | | 6 | ||
| Line 101: | Line 109: | ||
| 8mm×420mm | | 8mm×420mm | ||
| Smooth rod | | Smooth rod | ||
| + | | | ||
|+ | |+ | ||
| 2 | | 2 | ||
| Line 115: | Line 124: | ||
| 225mm×225mm print top plate | | 225mm×225mm print top plate | ||
| Thick Sheet | | Thick Sheet | ||
| + | | | ||
|+ | |+ | ||
| 1 | | 1 | ||
| 140mm×225mm print bottom plate | | 140mm×225mm print bottom plate | ||
| Thick Sheet | | Thick Sheet | ||
| + | | | ||
|+ | |+ | ||
| 1 | | 1 | ||
| 840mm×5mm T5 pitch timing belt | | 840mm×5mm T5 pitch timing belt | ||
| Belt | | Belt | ||
| + | | | ||
|+ | |+ | ||
| 1 | | 1 | ||
| 1380mm×5mm T5 pitch timing belt | | 1380mm×5mm T5 pitch timing belt | ||
| Belt | | Belt | ||
| + | | | ||
|+ | |+ | ||
| 5 | | 5 | ||
| NEMA 17 bipolar stepper motor | | NEMA 17 bipolar stepper motor | ||
| Stepper | | Stepper | ||
| + | | | ||
|+ | |+ | ||
| 50 | | 50 | ||
| small cable binder / ziptie | | small cable binder / ziptie | ||
| Misc | | Misc | ||
| + | | | ||
|+ | |+ | ||
| 1 | | 1 | ||
| Line 156: | Line 171: | ||
| If using opto endstops | | If using opto endstops | ||
|} | |} | ||
| + | |||
| + | We have all the M8 rod, the M8 washers, all the M3 and M4 parts. | ||
Revision as of 08:39, 23 May 2011
Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa
Build instructions: File:Prusa Mendel Visual Instructions (Mininum Resolution).pdf
BOM: --
| Quantity | Description | Type | Comments |
|---|---|---|---|
| 83 | M8 nut | Fastener | Buy a 100-pack to be on the safe side. |
| 93 | M8 washer | Fastener | Buy a 100-pack to be on the safe side. |
| 6 | M8×30 mudguard / fender washers | Fastener | |
| 2 | M4×20 bolt | Fastener | |
| 2 | M4 nut | Fastener | |
| 2 | M4 washer | Fastener | |
| 22 | M3×10 bolt | Fastener | |
| 16 | M3×25 bolt | Fastener | Or eight M3×25 bolt plus eight M3x20 bolts, see §8 steps 5 and 13 for details. |
| 4 | M3×40 bolt | Fastener | |
| 70 | M3 washer | Fastener | |
| 40 | M3 nut | Fastener | Eight optionally locknut / stop nut / nyloc |
| 2 | M3 grub screw / set screw | Fastener | |
| 3 | 608 roller skate / inline skate / skateboard bearing | Bearings | |
| 4 | ballpoint pen springs | Spring | |
| 6 | M8×370mm | Threaded rod | Three per side |
| 4 | M8×294mm | Threaded rod | Front / rear |
| 3 | M8×440mm | Threaded rod | Top / bottom |
| 2 | M8×210mm | Threaded rod | Z-leadscrew |
| 1 | M8×50mm | Threaded rod | Or bolt for X idler |
| 2 | 8mm×420mm | Smooth rod | |
| 2 | 8mm×406mm | Smooth rod | Y-bar |
| 2 | 8mm×350mm | Smooth rod | Z-bar |
| 1 | 225mm×225mm print top plate | Thick Sheet | |
| 1 | 140mm×225mm print bottom plate | Thick Sheet | |
| 1 | 840mm×5mm T5 pitch timing belt | Belt | |
| 1 | 1380mm×5mm T5 pitch timing belt | Belt | |
| 5 | NEMA 17 bipolar stepper motor | Stepper | |
| 50 | small cable binder / ziptie | Misc | |
| 1 | Wade's Geared Extruder | Or any other compatible extruder | |
| 1 | Electronics + endstops | This can be RAMPS, Gen6, Gen3, or anything else compatible | |
| 3 | 30mm×10mm Optoflags | Thin Sheet | If using opto endstops |
| 2 | 8mm ID spring | Spring | If using opto endstops |
We have all the M8 rod, the M8 washers, all the M3 and M4 parts.