Difference between revisions of "Reprap Prusa"
Jump to navigation
Jump to search
(Added photo) |
|||
| Line 219: | Line 219: | ||
[[Category:Projects]] | [[Category:Projects]] | ||
| + | [[Category:Projects (in progress)]] | ||
Revision as of 19:13, 17 December 2012
 |
This page is a stub. You can help by expanding it! This page is included in the list of stub pages. |
Main source of information: the Prusa page at reprap.org -- http://reprap.org/wiki/Prusa
Build instructions: File:Prusa Mendel Visual Instructions (Mininum Resolution).pdf
BOM: --
| Quantity | Description | Type | Comments |
|---|---|---|---|
| 83 | M8 nut | Fastener | Buy a 100-pack to be on the safe side. (GOT) |
| 93 | M8 washer | Fastener | Buy a 100-pack to be on the safe side. (GOT) |
| 6 | M8×30 mudguard / fender washers | Fastener | (NOT GOT) |
| 2 | M4×20 bolt | Fastener | (GOT) |
| 2 | M4 nut | Fastener | (GOT) |
| 2 | M4 washer | Fastener | (GOT) |
| 22 | M3×10 bolt | Fastener | (GOT) |
| 16 | M3×25 bolt | Fastener | Or eight M3×25 bolt plus eight M3x20 bolts, see §8 steps 5 and 13 for details. (GOT all options) |
| 4 | M3×40 bolt | Fastener | (GOT) |
| 70 | M3 washer | Fastener | (GOT) |
| 40 | M3 nut | Fastener | Eight optionally locknut / stop nut / nyloc (GOT) |
| 2 | M3 grub screw / set screw | Fastener | (GOT see Matt) |
| 3 | 608 roller skate / inline skate / skateboard bearing | Bearings | (GOT) |
| 4 | ballpoint pen springs | Spring | (GOT - various springs at space - others available) |
| 6 | M8×370mm | Threaded rod | Three per side (GOT) |
| 4 | M8×294mm | Threaded rod | Front / rear (GOT) |
| 3 | M8×440mm | Threaded rod | Top / bottom (GOT) |
| 2 | M8×210mm | Threaded rod | Z-leadscrew (GOT) |
| 1 | M8×50mm | Threaded rod | Or bolt for X idler (GOT) |
| 2 | 8mm×420mm | Smooth rod | (I have at home --'RepRap' Matt 22:23, 10 June 2011 (BST)) |
| 2 | 8mm×406mm | Smooth rod | Y-bar (I have at home --'RepRap' Matt 22:23, 10 June 2011 (BST)) |
| 2 | 8mm×350mm | Smooth rod | Z-bar (I have at home --'RepRap' Matt 22:23, 10 June 2011 (BST)) |
| 1 | 225mm×225mm print top plate | Thick Sheet | |
| 1 | 140mm×225mm print bottom plate | Thick Sheet | |
| 1 | 840mm×5mm T5 pitch timing belt | Belt | |
| 1 | 1380mm×5mm T5 pitch timing belt | Belt | |
| 5 | NEMA 17 bipolar stepper motor | Stepper | |
| 50 | small cable binder / ziptie | Misc | |
| 1 | Wade's Geared Extruder | Or any other compatible extruder | |
| 1 | Electronics + endstops | This can be RAMPS, Gen6, Gen3, or anything else compatible | |
| 3 | 30mm×10mm Optoflags | Thin Sheet | If using opto endstops |
| 2 | 8mm ID spring | Spring | If using opto endstops (GOT - various springs at space - others available) |
We have all the M8 rod, the M8 washers, all the M3 and M4 parts.
Printed Parts
| Quantity | Description | Type | Comments | Diagram |
|---|---|---|---|---|
| 2 | coupling | RP | 50px | |
| 3 | endstop-holder | RP | Done | 50px |
| 1 | x-carriage | RP | 50px | |
| 1 | x-end-idler | RP | 50px | |
| 1 | x-end-motor | RP | 50px | |
| 1 | y-motor-bracket | RP | Done | 50px |
| 2 | z-motor-mount | RP | 50px | |
| 4 | belt-clamp | RP | Done | 50px |
| 8 | bar-clamp | RP | Done | 50px |
| 2 | rod-clamp | RP | 50px | |
| 2 | pulley | RP | 50px | |
| 4 | frame-vertex with foot | RP | Done 1 | 50px |
| 2 | frame-vertex | RP | Done | 50px |
| 12 | pla-bushing | RP-PLA | check your build file, the file makes either 4 or 12 | 50px |
