Difference between revisions of "Silhouette Cameo"
(add some potentially useful link - will test later) |
(→Resources: * [https://www.silhouetteschoolblog.com/2016/07/silhouette-cameo-blades.html Guide to different blades (Silhouette School)]) |
||
| (3 intermediate revisions by 3 users not shown) | |||
| Line 7: | Line 7: | ||
|location=Textiles Workshop | |location=Textiles Workshop | ||
|induction=No | |induction=No | ||
| + | |team=Craft & Textiles | ||
}} | }} | ||
| Line 24: | Line 25: | ||
==Machine Setup== | ==Machine Setup== | ||
| − | + | ||
| + | It is worth keeping the backing sheet for the cutting mat. It stops you from needing to refresh the spray mount so often when the glue dries out. | ||
| + | |||
| + | When spraying with spray mount it's worth covering the non-sticky sections of the mat with masking tape, else the rollers of the machine pick up the glue which can effect how well it works. | ||
| + | |||
| + | Its generally worth using the cutting mat most of the time even if you are cutting a full width bit of vinyl. Unless you are a wizard at getting your material perfectly straight the rollers tend towards eating it. | ||
| + | |||
| + | The blade depth doesn't need to be stuck out lots and lots if you are cutting a thin material. For vinyl, paper and thing card usually setting 2 is sufficient. | ||
| + | |||
| + | Before cutting its worth removing the blade to check it doesn't have a build up of fluff round the razor. When cleaning it beware cutting hazards. | ||
| + | |||
| + | Make sure the blade is seated back where it was when you replace it. | ||
==Using the PC software== | ==Using the PC software== | ||
| Line 39: | Line 51: | ||
* [http://edutechwiki.unige.ch/en/Silhouette_Cameo Silhouette Cameo (EduTech Wiki)] | * [http://edutechwiki.unige.ch/en/Silhouette_Cameo Silhouette Cameo (EduTech Wiki)] | ||
* [https://libertyseeds.ca/2017/12/08/A-better-open-source-extension-for-Silhouette-Cameo-Inkscape-and-Ubuntu/ Silhouette Cameo using Inkscape (libertyseeds.ca)] | * [https://libertyseeds.ca/2017/12/08/A-better-open-source-extension-for-Silhouette-Cameo-Inkscape-and-Ubuntu/ Silhouette Cameo using Inkscape (libertyseeds.ca)] | ||
| − | * [https://github.com/fablabnbg/inkscape-silhouette/pull/45 Multiple action with Inkscape] | + | * [https://github.com/fablabnbg/inkscape-silhouette/pull/45 Multiple action with Inkscape (github.com)] |
| + | * [https://www.silhouetteschoolblog.com/2016/07/silhouette-cameo-blades.html Guide to different blades (Silhouette School)] | ||
==See also== | ==See also== | ||
Revision as of 21:42, 30 July 2019
 |
This page is a stub. You can help by expanding it! This page is included in the list of stub pages. |
| Silhouette Cameo | |
|---|---|
 | |
| Manufacturer | Silhouette |
| Model | Cameo 3 |
| Obtained | Purchased through Pledge Drive early 2018 |
| Location | Textiles Workshop |
| Team | Craft & Textiles |
| Induction Required | No |
| Tools: all pages • list • Power Tools • Broken tools {{}} | |
The Silhouette Cameo is a computer controlled cutter that can cut through vinyl, card, fabric and paper up to 12 inches wide.
The Cameo supports automated cutting heads, has two carriages (so draw and cut operations can be done in one pass) plus registration marks for aligment, and more.
It was purchased through a pledge drive in early 2018.
Manuals
Software
- Silhouette Studio - basic edition is free, available here.
Induction Notes
non-induction machine.
Machine Setup
It is worth keeping the backing sheet for the cutting mat. It stops you from needing to refresh the spray mount so often when the glue dries out.
When spraying with spray mount it's worth covering the non-sticky sections of the mat with masking tape, else the rollers of the machine pick up the glue which can effect how well it works.
Its generally worth using the cutting mat most of the time even if you are cutting a full width bit of vinyl. Unless you are a wizard at getting your material perfectly straight the rollers tend towards eating it.
The blade depth doesn't need to be stuck out lots and lots if you are cutting a thin material. For vinyl, paper and thing card usually setting 2 is sufficient.
Before cutting its worth removing the blade to check it doesn't have a build up of fluff round the razor. When cleaning it beware cutting hazards.
Make sure the blade is seated back where it was when you replace it.
Using the PC software
 |
This section requires cleaning up! The specific problem is: Blank section. Please help improve this page if you can. Use the talk page to discuss suggestions. (March 2019) |
Special attention areas
|
This section requires cleaning up! The specific problem is: Move info out of Google group message Please help improve this page if you can. Use the talk page to discuss suggestions. (March 2019) |
some suggestions were offered by Arthur Moore during the pledge drive
Resources
- Advertising video clip (YouTube)
- Silhouette Cameo (EduTech Wiki)
- Silhouette Cameo using Inkscape (libertyseeds.ca)
- Multiple action with Inkscape (github.com)
- Guide to different blades (Silhouette School)