Difference between revisions of "Startrite Bandsaw"
m |
|||
| Line 21: | Line 21: | ||
Blade length is 3200mm / 126" | Blade length is 3200mm / 126" | ||
| − | The first blade bought is a Morse M42 bimetal 10-14tpi [http://bandsawblog.com/variable-pitch-band-saw-blades-when-is-it-used/ varipitch] from [http://www.bandsawblades-direct.co.uk/Bandsaw_Blades_Direct.html Bandsaw Blades Direct] in Heanor. This is a general-purpose production-quality blade for cutting materials between 6mm and 35mm in thickness. | + | The first blade bought is a MK Morse M42 bimetal 1/2" x 10-14tpi [http://bandsawblog.com/variable-pitch-band-saw-blades-when-is-it-used/ varipitch] from [http://www.bandsawblades-direct.co.uk/Bandsaw_Blades_Direct.html Bandsaw Blades Direct] in Heanor. This is a general-purpose production-quality blade for cutting materials between 6mm and 35mm in thickness. A second, coarser, 3/4" x 6-10tpi [http://bandsawblog.com/variable-pitch-band-saw-blades-when-is-it-used/ varipitch] blade has been bought for trial when the existing blade fails, which we're told should last longer (fewer teeth within the material being cut means that they don't overheat) |
| − | + | Blade Break-In: Extremely Important (from [http://www.mkmorse.com/PDFs/MORSEBANDCAT.pdf MK Morse blade materials]) | |
| + | |||
| + | The extremely sharp tooth points and edges of new blades must be broken-in before applying full feed pressure to the blade. A good analogy is that of writing with a freshly sharpened wooden pencil. | ||
| + | |||
| + | Reccommended Break-In Procedure | ||
| + | * Maintain proper blade speed for the material to be cut. | ||
| + | * Reduce blade feed pressure or feed rate by 50% for the first 50 to 100 square inches of material cut. | ||
| + | * Gradually increase feed pressure or feed rate after break-in to target pressure or rate. | ||
| + | |||
| + | Further information concerning [http://littlemachineshop.com/Info/bandsaw.php blade selection], [http://www.mkmorse.com/PDFs/MORSEBANDCAT.pdf MK Morse blade materials] [http://www.detroitbandsaw.com/store.asp?pid=24064 and troubleshooting]. Possible sources of replacement parts: [http://www.carterproducts.com/band-saw-products/band-saw-wheels-tires tyres and guides] and [http://www.ebay.co.uk/usr/bandsaw-tire-warehouse tyres] | ||
A trial (May - June 2016) of lower cost HSS fixed-pitch blades showed no advantages in cost / lifetime, but showed that one real advantage of the vary-pitch blades is that they don't screech - which the fixed-pitch ones did. | A trial (May - June 2016) of lower cost HSS fixed-pitch blades showed no advantages in cost / lifetime, but showed that one real advantage of the vary-pitch blades is that they don't screech - which the fixed-pitch ones did. | ||
| − | |||
| − | |||
== Recommended Regular Maintenance == | == Recommended Regular Maintenance == | ||
Revision as of 13:10, 31 October 2016
Known as Willow.
See the back story at: Startrite_metal_bandsaw_pledge
Specification
3 (12") wheels, 5 speed, 24" throat bandsaw.
Cast-iron two-part tiltable table.
Powered from 415V three phase supply.
Usage
This tool is intended for cutting a range of non-ferrous and non-metallic materials (see the [handbook]); in the Hackspace, this is intended only for metal cutting, and the blade installed reflects this.
Safety
Blades and Maintenance
Blade length is 3200mm / 126"
The first blade bought is a MK Morse M42 bimetal 1/2" x 10-14tpi varipitch from Bandsaw Blades Direct in Heanor. This is a general-purpose production-quality blade for cutting materials between 6mm and 35mm in thickness. A second, coarser, 3/4" x 6-10tpi varipitch blade has been bought for trial when the existing blade fails, which we're told should last longer (fewer teeth within the material being cut means that they don't overheat)
Blade Break-In: Extremely Important (from MK Morse blade materials)
The extremely sharp tooth points and edges of new blades must be broken-in before applying full feed pressure to the blade. A good analogy is that of writing with a freshly sharpened wooden pencil.
Reccommended Break-In Procedure
- Maintain proper blade speed for the material to be cut.
- Reduce blade feed pressure or feed rate by 50% for the first 50 to 100 square inches of material cut.
- Gradually increase feed pressure or feed rate after break-in to target pressure or rate.
Further information concerning blade selection, MK Morse blade materials and troubleshooting. Possible sources of replacement parts: tyres and guides and tyres
A trial (May - June 2016) of lower cost HSS fixed-pitch blades showed no advantages in cost / lifetime, but showed that one real advantage of the vary-pitch blades is that they don't screech - which the fixed-pitch ones did.
Recommended Regular Maintenance
From the [handbook]
- Weekly
Remove embedded chips from the bandwheel tyres Clean upper and lower blade guide assemblies and check for wear
- Monthly
Check condition and tension of vee belts (motor drive cabinet)
- General
Clean and lubricate working parts as required. (The bandwheels have sealed-for-life bearings which do not require further lubrication. Check that the operating speed is set appropriately for the blade in use (to be determined and documented) and check availability of blades.