Difference between revisions of "Bat Box"
Jump to navigation
Jump to search
Note: Also available as a PDF File:BatBox Workshop.pdf
(6 intermediate revisions by the same user not shown) | |||
Line 9: | Line 9: | ||
|members= | |members= | ||
|status=Complete | |status=Complete | ||
− | |type= | + | |type=workshop |
|livestatus= | |livestatus= | ||
|qrmode=1 | |qrmode=1 | ||
Line 26: | Line 26: | ||
#Mark out the wood with a marker pen or pencil | #Mark out the wood with a marker pen or pencil | ||
#[[Table Saw]] to do the majority of the cuts. | #[[Table Saw]] to do the majority of the cuts. | ||
− | #For the side pieces with angled tops, I used the [[Sliding | + | #For the side pieces with angled tops, I used the [[Sliding Mitre Saw]]. |
#Hand Miter Saw to do the 1mm deep bat ladder on the back piece. | #Hand Miter Saw to do the 1mm deep bat ladder on the back piece. | ||
#[[Cordless_Drills|Impact Driver]] to screw everything together. | #[[Cordless_Drills|Impact Driver]] to screw everything together. | ||
Line 39: | Line 39: | ||
File:Bat Box - Finished 1.jpg|The finished bat box | File:Bat Box - Finished 1.jpg|The finished bat box | ||
File:Bat Box - Finished 2.jpg|The finished bat box | File:Bat Box - Finished 2.jpg|The finished bat box | ||
+ | </gallery> | ||
+ | |||
+ | ==Workshop July 2019== | ||
+ | |||
+ | The workshop we ran in July 2019 involved making a Kent style bat box as advised by the Wildlife Trust. Here are the plans! | ||
+ | |||
+ | <gallery mode=packed-hover heights=600px> | ||
+ | File:BATBOX1.PNG | ||
+ | File:BATBOX2.PNG | ||
+ | </gallery> | ||
+ | |||
+ | {{note|Also available as a PDF [[File:BatBox Workshop.pdf|Here]]}} | ||
+ | |||
+ | Here are some pictures of the event: | ||
+ | <gallery mode=packed-hover heights=300px> | ||
+ | File:BatBox Workshop July2019 1.jpg | ||
+ | File:BatBox Workshop July2019 2.jpg | ||
+ | File:BatBox Workshop July2019 3.jpg | ||
</gallery> | </gallery> |
Latest revision as of 08:21, 12 July 2019
Bat Box | |
---|---|
Primary Contact | Danspencer101 |
Created | 23/06/2019 |
Completed | 23/06/2019 |
Status | Complete |
Type | Workshop Activity |
QR code |
I had a go at making a Bat Box from plans on the Nottinghamshire Wildlife Trust website.
The wood (6" x 1" x 1200mm) was obtained from Harlow Bros. It can be brought in 4m-ish lengths for around £7. They cut it down for free into three manageable lengths that would fit into my car.
Plans from the Wildlife Trust Website
Method
The method of manufacture is as follows:
- Mark out the wood with a marker pen or pencil
- Table Saw to do the majority of the cuts.
- For the side pieces with angled tops, I used the Sliding Mitre Saw.
- Hand Miter Saw to do the 1mm deep bat ladder on the back piece.
- Impact Driver to screw everything together.
- Laser Cutter to engrave logos.
- Seal gaps with wood glue.
Gallery
Workshop July 2019
The workshop we ran in July 2019 involved making a Kent style bat box as advised by the Wildlife Trust. Here are the plans!
![Note Note](/images/thumb/6/60/Bulbgraph.png/18px-Bulbgraph.png)
Here are some pictures of the event: