Bambu Lab A1 mini: Difference between revisions
Bauhaus1919 (talk | contribs) |
Bauhaus1919 (talk | contribs) |
||
| Line 65: | Line 65: | ||
In preview tab of Bambu Studio choose "Print plate", this will Send the sliced code to the printer and the print job will begin. | In preview tab of Bambu Studio choose "Print plate", this will Send the sliced code to the printer and the print job will begin. | ||
== Printing from a | == Printing from a Micro SD card == | ||
You will need to have saved your sliced object to a Micro SD card. | You will need to have saved your sliced object to a Micro SD card. | ||
Revision as of 17:27, 10 August 2024
| Bambu Lab A1 mini | |
|---|---|
 | |
| Manufacturer | Bambu |
| Model | A1 mini |
| Location | 3D Printer Area |
| Team | 3D Printing |
| Induction Required | No |
| Tools: all pages • list • Power Tools • Broken tools {{}} | |
This printer was installed in the Space on 7th August, 2024.
Buying Filaments
The A1 mini takes 1.75mm filament, so choose some PLA or PETG in your favourite colour.
The nozzle in the A1 mini is not hardened so do not use filaments that contain "fillers" such as Carbon fiber or glow in the dark - they will ruin the printer nozzle. (We will be getting a hardened nozzle in the near future if the use of the A1 mini justifies the expense)
PETG prints well, is tougher than PLA but can create strings if printing too fast - is better that PLA when coming into contact with water and will resist higher ambient temperatures than PLA.
PLA gives good detail and clean prints - is brittle and is not good to use in moist conditions - it will also tend to misform in high ambient temperatures.
You can buy branded Bambu filament off the Bambu store, or just shop about on Amazon.
Slicer choice
The Recommended slicer for the A1 mini is Bambu studio. Download and install from the Bambulab site:.
https://bambulab.com/en/download/studio
Using Bambu Studio slicer on your own laptop within Hackspace
If you are connected to the LAN in Hackspace and the A1 mini is powered on, you should be able to "see it" and select it in Bambu Studio The printer should appear in Bambu Studio under the device dropdown. If it doesn't, you may need to adjust your firewall settings.
When connecting to the printer, it will ask for a PIN code which can be found on the printer under Settings > LAN Only. Please do not press the refresh icon, as everyone else that already has setup their slicer will need to reset their PIN code.
Do not register the printer to any Bambu account - please leave this in LAN Only mode.
Using Bambu Studio outside of Hackspace
You do not have to be in HackSpace to use the A1 mini printer simply install Bambu studio, select the A1 mini as your printer.
Slicing the part
Once the printer is configured in Bambu Studio, import your object (the slicer accepts a number of file formats) and orient it to minimise overhangs. Supports can be enabled if necessary.
Ensure that you are slicing for the correct filament you have loaded or will load into the printer.
Click the Preview tab to slice the model.
You can move up and down between the layers to ensure certain areas will provide enough strength you can go back to the prepare tab to adjust your settings and reslice.
Preapring the machine to print
Check your filament is loaded. Load your filament by following the instructions on the A1 mini screen under Filament > load. Choose the filament type Generic PLA or Generic PETG etc.
Check that the build plate is correctly positioned.
Printing direct to the printer from Bambu Studio
You have to be connected to the LAN in Hackspace and be able to "see" the A1 mini.
In preview tab of Bambu Studio choose "Print plate", this will Send the sliced code to the printer and the print job will begin.
Printing from a Micro SD card
You will need to have saved your sliced object to a Micro SD card.
In "Preview tab" of Bambu Studio, choose the dropdown from "Print plate" and select "Export plate sliced file"
Click this and you will be prompted to save the file in a name format yourname_m.gcode.3mf.
Put this file on your Micro SD card and head off to Hackspace.
Insert your Micro SD card into the A1 mini, your sliced objects will appear for printing on the A1 mini screen. REMEMBER TO REINSERT THE ORIGINAL SD CARD AFTER YOUR PRINT HAS FINISHED
Choose the object and hit print.
Printing operation
The printer will go through its startup routine (which includes auto bed levelling), a little shaking too.
A purge line will be printed on the front of the build plate.
When the print is completed - wait a few minutes for the build plate to cool down and then it should be very easy to remove your printed item.
Cleaning up
Unload your filament by following the instructions on the A1 mini screen under Filament > unload.
Ensure the build plate is free of your printed item, supports and any filament purge lines (found at the front of the build plate).