Yrs3d: Difference between revisions
| Line 8: | Line 8: | ||
the hackspace printer will require (at least) Electonics, and possibly other bits. | the hackspace printer will require (at least) Electonics, and possibly other bits. | ||
---- | ---- | ||
== YRS Build Log == | == YRS Build Log NEWEST AT TOP == | ||
Box of remaining parts tidied. | |||
All non YRS 3d Parts (i.e. hackspace reprap parts) moved to shelf to | |||
try and help with keeping things in order. | |||
Only major bits left for fitting are hotbed, hot end and the electronics. | |||
chris 26 Dec | |||
Extruder built 26/dec chris | |||
X carriage movement a bit stiff, a couple of tries using washers/spacers to make it run better | |||
it now moves reasonably, further adjustment may be needed once the electronics/motors are connected and under power testing can be done. | |||
X assembly built and fitted | |||
X Smooth rods too long (length for non LM8 X ends) | X Smooth rods too long (length for non LM8 X ends) | ||
Cut down by 15mm to 435mm | Cut down by 15mm to 435mm | ||
Z motors added with coupling rods - motors not screwed in place | Z motors added with coupling rods - motors not screwed in place | ||
| Line 22: | Line 32: | ||
to use tie wraps to hold them in place and redude out of alignment rough spots/vibration. | to use tie wraps to hold them in place and redude out of alignment rough spots/vibration. | ||
X | X-end idler was broken | ||
New part printed | |||
== Next steps == | == Next steps == | ||
Revision as of 16:38, 26 December 2013
YRS 3D Printer Status and Log
The YRS 3d Printer is being 'lent'/allowed to be completed by the owners the ail is to complete this and then finish the Hackspace owned printer to have a '3d Printer as a tool' available in the space.
The YRS printer is basically complete and the build should go fairly quickly the hackspace printer will require (at least) Electonics, and possibly other bits.
YRS Build Log NEWEST AT TOP
Box of remaining parts tidied. All non YRS 3d Parts (i.e. hackspace reprap parts) moved to shelf to try and help with keeping things in order. Only major bits left for fitting are hotbed, hot end and the electronics. chris 26 Dec
Extruder built 26/dec chris
X carriage movement a bit stiff, a couple of tries using washers/spacers to make it run better it now moves reasonably, further adjustment may be needed once the electronics/motors are connected and under power testing can be done.
X assembly built and fitted
X Smooth rods too long (length for non LM8 X ends)
Cut down by 15mm to 435mm
Z motors added with coupling rods - motors not screwed in place notes on web seem to indicate that it may be better to not screw these down but to use tie wraps to hold them in place and redude out of alignment rough spots/vibration.
X-end idler was broken New part printed
Next steps
Build Extruder
Completed. Extruder all built and placed on x carriage, not screwed down yet as need to check hot end fit/alignment etc.
Build Hot end
All Done. Opon examination of the hot end bag it turned out that the hot end came pre-built all looks in good shape, ready for mounting. Not mounted yet as it is a bit fragile and probaly needs to be done after alignment/coarse testing of movement.
Fit Extruder/hot end
Build bed (heated plate etc)
Sorted all the parts.
It looks like the supplied bolts require all the heated bed hols to be redrilled larger these holes are very close to the corners !
Decided to have a check/think before madly drilling bigger holes.
Electonics
All checked (as in stock checked :-) ) and complete this is probably next step now to allow some motion testing the X - axis is still stiff/catching and may need some more work unless it frees up under power.