Plotter: Difference between revisions
mNo edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
===HP DesignJet 600=== | |||
Roll-fed 600dpi plotter using (original) DeskJet Black Ink cartridge printheads. | Roll-fed 600dpi plotter using (original) DeskJet Black Ink cartridge printheads. | ||
| Line 7: | Line 7: | ||
Serial and Parallel interface - choose from control panel - currently (5/1/2014) connected to quorra using a long parallel cable. | Serial and Parallel interface - choose from control panel - currently (5/1/2014) connected to quorra using a long parallel cable. | ||
===Switching on=== | |||
Before switching on, make sure that the paper roll is in place, positioned against the right-hand alignment mark, and not torn so as to prevent the printhead from moving. | Before switching on, make sure that the paper roll is in place, positioned against the right-hand alignment mark, and not torn so as to prevent the printhead from moving. | ||
| Line 15: | Line 15: | ||
When ready, the display will say so. | When ready, the display will say so. | ||
===Printing=== | |||
There is a driver installed under Windows XP on quorra. Other operating systems may also have drivers - these have not been tested ([[#Testing and Settings|see here]]). | There is a driver installed under Windows XP on quorra. Other operating systems may also have drivers - these have not been tested ([[#Testing and Settings|see here]]). | ||
| Line 25: | Line 25: | ||
After a job is completed, the plotter waits for over a minute (see the display) for the ink to dry before cutting the paper (this is for when transparency film is being printed). Do not try and manually feed or cut the paper during this time - it will take you longer than this to re-load and align the paper once more. | After a job is completed, the plotter waits for over a minute (see the display) for the ink to dry before cutting the paper (this is for when transparency film is being printed). Do not try and manually feed or cut the paper during this time - it will take you longer than this to re-load and align the paper once more. | ||
===Ink=== | |||
The DesignJet 600 takes a pair of ink-cartridge / printheads, type HP26 (or equivalent). A supply of remanufactured ones is currently available. | The DesignJet 600 takes a pair of ink-cartridge / printheads, type HP26 (or equivalent). A supply of remanufactured ones is currently available. | ||
===Testing and Settings=== | |||
Testing and printing has so far only been done from a .PDF file under Windows XP. No changes were made to settings from the printer's own control panel, which are set to: ... {to do} | Testing and printing has so far only been done from a .PDF file under Windows XP. No changes were made to settings from the printer's own control panel, which are set to: ... {to do} | ||
Other operating systems and document types have yet to be tested. Please update the following list when done: | Other operating systems and document types have yet to be tested. Please update the following list when done: | ||
'''OSX is not supported in anyway''' | |||
{| class="wikitable" border="1" | {| class="wikitable" border="1" | ||
| Line 90: | Line 92: | ||
|} | |} | ||
===Network=== | |||
The printer now has a JetDirect card install and has been assigned the IP 10.0.0.97 | |||
===Future=== | |||
A spindle needs to be fabricated to keep the paper roll from drifting in position. | A spindle needs to be fabricated to keep the paper roll from drifting in position. | ||
Revision as of 19:36, 13 April 2016
HP DesignJet 600
Roll-fed 600dpi plotter using (original) DeskJet Black Ink cartridge printheads.
The standard memory installed in this plotter is 4MB, upgradeable to 20MB to enable larger / more complex plots to be printed.
Serial and Parallel interface - choose from control panel - currently (5/1/2014) connected to quorra using a long parallel cable.
Switching on
Before switching on, make sure that the paper roll is in place, positioned against the right-hand alignment mark, and not torn so as to prevent the printhead from moving.
Switch on, button at the left-hand side. The printer will go through an extensive self-test routine, which includes sweeping back and forth across the paper to see how wide it is.
When ready, the display will say so.
Printing
There is a driver installed under Windows XP on quorra. Other operating systems may also have drivers - these have not been tested (see here).
There are probably more printer settings that need to be checked when printing on a device like this, where the paper size is not obvious. The paper roll is A0 (841mm) width, to check that this is the current selection when the print dialog is opened from the application that you want to print from.
The only other option to check is under printer / advanced options, where there is an option to 'print as bitmap image'. This should not be selected, as it slows down transmission of the data increasing the possibility of errors (e.g. an A4 document printed at 400%, which was the test piece, requires the transmission of 210MB of data in 'bitmap image' mode, compared with under 2MB otherwise using the plotters internal intelligence.
After a job is completed, the plotter waits for over a minute (see the display) for the ink to dry before cutting the paper (this is for when transparency film is being printed). Do not try and manually feed or cut the paper during this time - it will take you longer than this to re-load and align the paper once more.
Ink
The DesignJet 600 takes a pair of ink-cartridge / printheads, type HP26 (or equivalent). A supply of remanufactured ones is currently available.
Testing and Settings
Testing and printing has so far only been done from a .PDF file under Windows XP. No changes were made to settings from the printer's own control panel, which are set to: ... {to do}
Other operating systems and document types have yet to be tested. Please update the following list when done:
OSX is not supported in anyway
| Operating System | File Type | Working OK |
|---|---|---|
| Windows XP | OK | |
| .DOC | ||
| AutoCAD | ||
| .PPT | ||
| Mac OS | ||
| .DOC | ||
| AutoCAD | ||
| .PPT | ||
| Linux | ||
| .DOC | ||
| AutoCAD | ||
| .PPT |
Network
The printer now has a JetDirect card install and has been assigned the IP 10.0.0.97
Future
A spindle needs to be fabricated to keep the paper roll from drifting in position.
Links and references
http://www.linuxfoundation.org/collaborate/workgroups/openprinting/macosx/hpijs#Printers