Sagar Chisel Mortiser

Purchased by a pledge drive, and currently being installed in the workshop.

About the Machine

Manufactured by J. Sagar & Co. Halifax, based on promotional materials it appears to be based on a design already in production by 1909, and subsequently re-designed in the late 20's to run on electrical rather than overhead belt power, living history right here in the hackspace no less.

What does it do?

Put simply, it is a drill for square holes.

More comprehensively, A hollow chisel mortiser has a auger bit running inside a hollow, square chisel. Pulling the lever down brings the auger into the wood, cutting away the bulk of the material, before the chisel follows ¹/₁₆" behind, taking away the material in the corners to give a square hole.

Why do we want to do that?

A simple Mortise and Tenon joint.

Mortise and Tenon joints in all their many forms, remain the strongest and most secure method of joining two pieces of wood.

Cutting a tight-fitting hole, in a piece of wood, which is dead square in all three dimensions, using nothing more than a mallet and chisel, requires a substantial amount of skill and practice;^[1] not to mention a reasonable amount of effort; by contrast a chisel mortiser allows all this to be done with little more than a push of a button, turn of a wheel and pull of a lever.^[2]

It's hoped that this will open up some more ambitious and structural woodworking projects to all comers.^[3]

Installation Progress

The machine is now in position, but inoperative until the power is connected.

Installation Work

Completed

The bolt which secures the chisel in position, unfortunately seized and subsequently sheered on attempting to free it. The remainder of the bolt has been drilled out, the residue of the threads removed with a tap, and a replacement (and spare) set-screw of the appropriate size (⁵/₁₆^th Whitworth) has been sourced.

Machine has been stripped, wire brushed, cleaned and coated with a thin coat of light oil.

Threads on arm have been cleared with ⁷/₁₆^ths Whitworth tap.

Ways on the table have been thoroughly cleaned, all ways have been lubricated using light oil (debatable as to whether way-lube would be beneficial or cause excessive buildup of sawdust).

Damaged wiring to motor removed, motor has been stripped, all dust and chips removed, and the bearings checked, top bearing cover found to not be attached, needs 2 × 0BA 2" machine screws. sourced.

Chisel and auger sharpened, fitted and adjusted.

New depth stop machined from ½"^O/_D steel pipe from metalwork scrap bin.

Chisel collet has significant damage, still serviceable as is but replacement best course of action long term.

Auger collet has burr on bottom, could damage chisel holder assembly bearing surface during maintainance if not addressed.

Z-axis travel rack missing tooth, has been replaced with two set screws.

Awaiting Competion

• Electrical Hook Up
• Wire in starter
• Replace grease in motor bearings (at a minimum, lower bearing needs urgent top-up).
• Fit Sacrificial Top to Table
  • Re-set quadrant to table height.
• Machining
  • New collet for chisels from bar.
  • Remove Auger collet from spindle, turn chamfer on lower edge to remove burr (to protect bearing race chisel holder during future maintainance).
  • Hand-fit new tooth for rack and arrange to braze into position.
• Re-Paint.
  • Sign-write lever with names of Pledges.

Parts

Parts sourced:

• 2 × ⁵/₁₆ BSW 2½" allen head set screws

Parts on order:

• 12m of 5 core, 2.5mm² armoured cable.
• 20A rotary isolator.
• 440v DOL Motor Starter, with 1.8-2.5A thermal overload.

Parts to order:

• ½ or ¾ ply - 2'6" by 8" — sacrificial table top.
• New tooling.
• 2 × 0BA 2" Machine Screw.
• Paint.
• 1½" round bar, free machining grade - spring steel.
• ¼" cast iron bar.

Costs:

Item	Qty.	Price per each	Total cost	Running total
# Morticer	1	£80.00	£80.00	£80.00
Van Hire	1	£95.00	£95.00	£175.00
Fuel	1	£20.03	£20.03	£195.03
BSW Bolts	2	£1.50	£3.00	£198.03
3 Ph Cable	12m	£2.78	£33.36	£231.39
Isolator	1	£11.50	£11.50	£242.89
DOL Starter	1	£35.49	£35.49	£278.38

Standard Operating Procedure

First select dimensions and layout of the joints, appropriate to the timbers to be joined.

Layout

1. On each piece to be mortised, determine a "reference face" and mark it lightly in pencil.
2. Prepare a "rod"
   1. Take a piece of scrap timber, ply or MDF, with at least one straight edge, and cut one end perpendicular to the straight edge.
   2. Using a sharp, dark pencil and a steel rule or combination square, make marks at the following distances: reference face to near side of mortise, reference face to far side of mortise, end of timber to beginning of mortise, end of timber to end of mortise and (if required) end of timber to end of haunch.
   3. If space allows, clearly write what each mark refers to above it.
3. Use the rod to make marks on each piece indicating the distances.
4. Using a Set-Square or Combination Square join these marks to form a rectangle indicating material to be removed.
5. Cross hatch the area to be removed

Setup

If the size of chisel required is not currently installed, you may need to change the tooling at this point. Where the chisel is too small and only one or two mortises are to be cut, it may be more sensible to cut the mortise along one side, then re-align the chisel and work the opposite side; where mortises of intermediate width between two chisel sizes are to be cut, this is the only method available.

1. Ensure the machine is switched off.
2. Approximately centre the table.
3. Raise the lever to bring the chisel clear of the bed. (N.B. Lifting the lever to vertical will result in the rack disengaging from the quadrant, allowing the mechanism to drop and potentially damaging it. Never lift the lever up completely vertical.)
4. Place the work flat on the table and close the vice.
5. Lower the lever until the tip of the auger is just above the work.
6. Line up the edge of the chisel with the edges of the marked area (It may be necessary to use a small Set-Square placed on the workpiece to assist.)
7. If making a stub mortise, bring the lever down until the cutting lip of the auger touches the workpiece, and bring the depth stop down in contact with the workpiece, mark this position, then raise the depth stop up by the desired amount, using the mark to measure from, and secure the depth stop with the set-screw.

Machining

See that the workpiece is aligned as in 6. above.

1. Ensure the auger is not in contact with the workpiece.
2. Press the green button to turn on the motor.
3. Pull the lever down firmly and smoothly, taking care not to force the auger into the work faster than it can remove wood.
4. When the depth stop is in contact or the chisel has cut through to the opposite side, raise the lever to remove the chisel.
5. Move the chisel to the opposite end^[4] of the mortice and align as per 6. above, stopping the machine if necessary.
6. Repeat steps 3. & 4., moving workpiece along after each cut working toward the initial cut made in 3.
7. Turn off the machine using the red button.
8. Clean up any chips generated.

Footnotes

1. Indeed, it is not enough to develop the skill once, regular practice is essential to continue making a good job of it.
2. The keen eyed reader will note that in the above advertisment, Sagar suggest that being usable by "a lad" was one of the machine's selling points.
3. Especially the author, who always enjoys mortising by hand to begin with, before getting part-way through and realising that He's ultimately rather lazy.
4. The reason for this step is that the chisel will cut straight down, when going through solid wood, but will be pushed very slightly towards the free space when working along a mortise. Best Practice is thus to, define both ends of the mortise as dead straight, by cutting through solid wood before removing the bulk of the waste is preferred.