Plotter: Difference between revisions
Photo |
No edit summary |
||
| Line 18: | Line 18: | ||
The standard memory installed in this plotter is 4MB, upgradeable to 20MB to enable larger / more complex plots to be printed. | The standard memory installed in this plotter is 4MB, upgradeable to 20MB to enable larger / more complex plots to be printed. | ||
Serial and Parallel interface | Serial and Parallel interface connected to the Embroidery PC (Fairuza) using a short pll cable with a usb adaptor. | ||
===Switching on=== | ===Switching on=== | ||
| Line 30: | Line 30: | ||
===Printing=== | ===Printing=== | ||
There is a driver installed under Linux on the | There is a driver installed under Linux on the Embroidery PC. | ||
{{note|Windows only has 32bit drivers available, so if you want to print from your own laptop, good luck! :)}} | |||
===Ink=== | ===Ink=== | ||
| Line 43: | Line 38: | ||
The DesignJet 600 takes a pair of ink-cartridge / printheads, type HP26 (or equivalent). A supply of remanufactured ones is currently available (in the green shopping back, under the plotter). | The DesignJet 600 takes a pair of ink-cartridge / printheads, type HP26 (or equivalent). A supply of remanufactured ones is currently available (in the green shopping back, under the plotter). | ||
=== | ===Settings=== | ||
Printing is possible from a .PDF file under Linux on the Embroidery PC. No changes to settings from the printer's own control panel are necessary. | |||
There are probably more printer settings that need to be checked when printing on a device like this, where the paper size is not obvious. The paper roll is A0 (841mm) width, to check that this is the current selection when the print dialog is opened from the application that you want to print from. | |||
''' | The only other option to check is under printer / advanced options, where there is an option to 'print as bitmap image'. This should ''not'' be selected, as it slows down transmission of the data increasing the possibility of errors (e.g. an A4 document printed at 400%, which was the test piece, requires the transmission of 210MB of data in 'bitmap image' mode, compared with under 2MB otherwise using the plotters internal intelligence. | ||
After a job is completed, the plotter waits for over a minute (see the display) for the ink to dry before cutting the paper (this is for when transparency film is being printed). Do not try and manually feed or cut the paper during this time - it will take you longer than this to re-load and align the paper once more. | |||
===Network=== | ===Network=== | ||
| Line 113: | Line 54: | ||
===Future=== | ===Future=== | ||
A spindle needs to be fabricated to keep the paper roll from drifting in position. | A spindle needs to be fabricated to keep the paper roll from drifting in position. {{low}} | ||
<H1>Links and references</H1> | <H1>Links and references</H1> | ||
Revision as of 13:07, 12 March 2019
| Plotter | |
|---|---|
 | |
| Manufacturer | HP |
| Model | DesignJet 600 |
| Location | Textiles Workshop |
| Team | Craft & Textiles |
| Induction Required | No |
| Tools: all pages • list • Power Tools • Broken tools {{}} | |
This page is about the HP DesignJet 600 plotter.
HP DesignJet 600
Roll-fed 600dpi plotter using (original) DeskJet Black Ink cartridge printheads.
The standard memory installed in this plotter is 4MB, upgradeable to 20MB to enable larger / more complex plots to be printed.
Serial and Parallel interface connected to the Embroidery PC (Fairuza) using a short pll cable with a usb adaptor.
Switching on
Before switching on, make sure that the paper roll is in place, positioned against the right-hand alignment mark, and not torn so as to prevent the printhead from moving.
Switch on, button at the left-hand side. The button detent is broken, but it can be held in by sliding the shim of wood tied around the housing over the switch. The printer will go through an extensive self-test routine, which includes sweeping back and forth across the paper to see how wide it is.
When ready, the display will say so.
Printing
There is a driver installed under Linux on the Embroidery PC.
Note: Windows only has 32bit drivers available, so if you want to print from your own laptop, good luck! :)Ink
The DesignJet 600 takes a pair of ink-cartridge / printheads, type HP26 (or equivalent). A supply of remanufactured ones is currently available (in the green shopping back, under the plotter).
Settings
Printing is possible from a .PDF file under Linux on the Embroidery PC. No changes to settings from the printer's own control panel are necessary.
There are probably more printer settings that need to be checked when printing on a device like this, where the paper size is not obvious. The paper roll is A0 (841mm) width, to check that this is the current selection when the print dialog is opened from the application that you want to print from.
The only other option to check is under printer / advanced options, where there is an option to 'print as bitmap image'. This should not be selected, as it slows down transmission of the data increasing the possibility of errors (e.g. an A4 document printed at 400%, which was the test piece, requires the transmission of 210MB of data in 'bitmap image' mode, compared with under 2MB otherwise using the plotters internal intelligence.
After a job is completed, the plotter waits for over a minute (see the display) for the ink to dry before cutting the paper (this is for when transparency film is being printed). Do not try and manually feed or cut the paper during this time - it will take you longer than this to re-load and align the paper once more.
Network
The printer now has a JetDirect card install and has been assigned the IP 10.0.0.97 on the space's network. however, the jetdirect card does not appear to work.
Future
A spindle needs to be fabricated to keep the paper roll from drifting in position. 
Links and references
http://www.linuxfoundation.org/collaborate/workgroups/openprinting/macosx/hpijs#Printers