Mini lathe: Difference between revisions

From Nottinghack Wiki
Jump to navigation Jump to search
mNo edit summary
PhillS (talk | contribs)
→‎Operation: Safety info added
 
(2 intermediate revisions by one other user not shown)
Line 6: Line 6:
|obtaineddate=June 2016
|obtaineddate=June 2016
|team=Metalworking
|team=Metalworking
|location=Upstairs Metalworking Area  
|location=Metalworking Area
 
Near back door
|induction=No
|induction=No
}}
}}
Line 20: Line 18:


==[[Myford Lathe/Operation|Operation]]==
==[[Myford Lathe/Operation|Operation]]==
==Safety==
As always at the Hackspace YOU are responsible for your own safety, proper machine operation and safety of those around you.
Borrowed most of the following from [http://www.mini-lathe.com/Mini_lathe/lathe_safety.htm Mini-lathe.com] & [http://www.lathes.co.uk/page13.html lathes.co.uk] --[[User:Lwk|'RepRap' Matt]]
* '''Always wear eye protection'''
* '''Wear short sleeve shirts, if possible, or shirts with snugly fitting cuffs if long sleeve'''
** Loose sleeves can catch on rotating work and quickly pull your hand or arm into harm's way. '''[[User:Lwk|'RepRap' Matt]] has the scar to prove this point!'''
* Remove wrist watches, necklaces, chains and other jewellery
* Tie back long hair so it can't get caught in the rotating work
* '''Never, ever, leave a chuck key in a chuck.'''
** Get in the habit of removing the chuck key immediately after use
** Never remove your hand from the chuck key when it is in the chuck
* Keep your fingers clear of the rotating work and cutting tools
* '''Avoid reaching over the spinning chuck'''
** Please do not use hand held tools or files on this machine with the spindle switched on. See below for use of emery cloth
* After setting up any turning job, take a moment to pull the job round by hand to check that everything clears
==Polishing/use of emery cloth==
The use of emery cloth for polishing is common practice, but carries a high risk to both machine and operator.
*'''HAND HELP EMERY CLOTH MUST NEVER BE USED''' Please see this link for the HSE recommended method of holding emery tape in a tool holder: https://www.hse.gov.uk/engineering/lathes.htm
*The abrasive dust will mix with any oils and form a grinding paste, which will ruin the slideways. Please clean all slideways thoroughly before AND after polishing.


==[[Myford_lathe/drill_and_thread_charts|Drill & Thread Charts]]==
==[[Myford_lathe/drill_and_thread_charts|Drill & Thread Charts]]==

Latest revision as of 17:20, 4 September 2024

Mini lathe
Manufacturer Generic Chinese
Model Mini Lathe
AKA {{{aka}}}
Obtained Pledge Drive (June 2016)
Location Metalworking Area
Team Metalworking
Induction Required No
Booking {{{booking}}}
Status Defunct
Tools:   all pageslistPower ToolsBroken tools     {{}}

about

https://littlemachineshop.com/info/minilathe.php

users guide

https://littlemachineshop.com/images/gallery/info/MiniLatheUsersGuide.pdf

Operation

Safety

As always at the Hackspace YOU are responsible for your own safety, proper machine operation and safety of those around you.

Borrowed most of the following from Mini-lathe.com & lathes.co.uk --'RepRap' Matt

  • Always wear eye protection
  • Wear short sleeve shirts, if possible, or shirts with snugly fitting cuffs if long sleeve
    • Loose sleeves can catch on rotating work and quickly pull your hand or arm into harm's way. 'RepRap' Matt has the scar to prove this point!
  • Remove wrist watches, necklaces, chains and other jewellery
  • Tie back long hair so it can't get caught in the rotating work
  • Never, ever, leave a chuck key in a chuck.
    • Get in the habit of removing the chuck key immediately after use
    • Never remove your hand from the chuck key when it is in the chuck
  • Keep your fingers clear of the rotating work and cutting tools
  • Avoid reaching over the spinning chuck
    • Please do not use hand held tools or files on this machine with the spindle switched on. See below for use of emery cloth
  • After setting up any turning job, take a moment to pull the job round by hand to check that everything clears


Polishing/use of emery cloth

The use of emery cloth for polishing is common practice, but carries a high risk to both machine and operator.

  • HAND HELP EMERY CLOTH MUST NEVER BE USED Please see this link for the HSE recommended method of holding emery tape in a tool holder: https://www.hse.gov.uk/engineering/lathes.htm
  • The abrasive dust will mix with any oils and form a grinding paste, which will ruin the slideways. Please clean all slideways thoroughly before AND after polishing.

Drill & Thread Charts