Cheesoid: Difference between revisions

From Nottinghack Wiki
Jump to navigation Jump to search
← Older editNewer edit →
No edit summary
Line 198: Line 198:


--[[User:Msemtd|Michael Erskine]] 15:26, 6 September 2011 (EST)
--[[User:Msemtd|Michael Erskine]] 15:26, 6 September 2011 (EST)
I need to spec and get a hold of some motors!


I've established that I want 160RPM 12V motors
I've established that I want 160RPM 12V motors
Line 236: Line 234:
Same one from another seller (maybe same seller!)...
Same one from another seller (maybe same seller!)...
* http://www.ebay.co.uk/itm/New-160RPM-Gear-Torque-DC-12V-Motor-Driver-Control-/250887708255?pt=LH_DefaultDomain_0&hash=item3a6a129e5f
* http://www.ebay.co.uk/itm/New-160RPM-Gear-Torque-DC-12V-Motor-Driver-Control-/250887708255?pt=LH_DefaultDomain_0&hash=item3a6a129e5f


Hmm, 150RPM 37mm Diameter...
Hmm, 150RPM 37mm Diameter...
Line 242: Line 239:
Looks the same as...
Looks the same as...
* http://www.pololu.com/catalog/product/1105
* http://www.pololu.com/catalog/product/1105
Awesomes!


OK, I've ordered a pair of 37mm 150RPM gearmotors from China - fingers crossed they're going to be suitable!


--[[User:Msemtd|Michael Erskine]] 9 September 2011 (EST)
--[[User:Msemtd|Michael Erskine]] 9 September 2011 (EST)


== A new development: Aug 2011 - give Cheesoid a proper brain with an old eeePC ==
== A new development: Aug 2011 - give Cheesoid a proper brain with an old eeePC ==

Revision as of 14:46, 14 September 2011

A comedy robot with sensory and existential issues.

"Why Cheesoid exist?"

Mitchell & Webb: Cheesoid

An unhappy robot designed to have a sense of smell but can only distinguish between its two operating modes: "CHEESE" and "PETROL".

Thoughts

Everybody loves robots: It's your plastic pal who's fun to have around! I'd like a robot too, and I'm going to build one goddamnit!!!

As with everything I want to build, it must be funny, and so Cheesoid is the ideal blueprint to follow.

It has (should have) speech limited to a number of pre-recorded phrases: -

  • "Cheese"
  • "Petril"
  • "Help! Cannot see! Can only smell!"
  • "Why Cheesoid exist?"
  • etc.

Basic Construction

I have a cardboard cylinder (slightly smaller than the original) and a silver "nose hose". The nose hose will contain a bent rod that will be rotated by a servo or stepper motor. The robot can run on top of a R/C car to begin with. The donated R/C car at the space has no battery and I couldn't get the motor to run!

I plan to cover Cheesoid in silver-grey paper.

The nose hose needs to be mounted in a shallow box which in turn is fixed to the body.

The "CHEESE" or "PETROL" mode switch must be authentic!

Voice capability will just be some sort of recordable button box.

Object detector (that initiates the smelling process) would be awesome.

The ability to actually distinguish between the smell of cheese and petrol would be crazy-awesome!

Need: -

  • R/C vehicle
  • silver-grey paper or card - using some silvery-blue slightly metallic wallpaper (recovered from skip) that reminds me of galvanised steel
  • nose rod and motor - have the stepper
  • voice
  • lamp eyes - one red, one green - Using LEDs and industrial lamp sockets (saved from skip)
  • flashing LEDS
  • automation!!!

Nose Stepper

A stepper motor will be used to drive the "nose". The curved nose hose is fixed to the body and doesn't rotate. Inside a rigid but bent rod will rotate, driven by the stepper. The stepper needs enough grunt! I have no idea how "grunt" is measured in ISO units - torque I guess. Speed and accuracy is not so important for this task but it is a learning experience.

So I chose a random biggish stepper motor (from the members' motor box)...

It has 6 wires that go to a 2x4 0.1" pitch connector. It says "MINEBEA" "TYPE 17PS-C035-03" -- hmmm...

1.7 inch, P = Precision, Hybrid, S = 3.6 Deg, C =2 & 4 Phase Hybrid, Motor Lengths = 0(?), Different Windings = 35, Version = 03.

OK, so the information on the side isn't much help in finding the voltage and current so using the magic knowledge on the pages listed above I gleaned some info using SCIENCE!!!!

The stepper turns out to be a Unipolar. It has 6 wires, 2 for the centre taps which should go to V+ and two each for the grounds of the half coils.

I identified the usage of the wires using my cheap multimeter and measured the half coil resistances: 36.9 ohms, 36.6 ohms, 36.7 ohms, 36.7 ohms.

Six wires
Brown Black Red
Green Orange White
Wire purpose
Coil B 1 Coil A Centre Coil B 2
Coil A 1 Coil B Centre Coil A 2

Driving it!


To be continued!!!

Display and Indicators

The eyes on the "real" Cheesoid just flash left-right, left-right with one eye being red and the other green. I'll stick with this for now as it's simple but I'm not sure I want to use two pins on my Xino. I'll look into that when I have the basics in place.

I have added an LCD display...

Why Cheesoid Exist?

This is a Seiko L2012 LCD module (File:Seiko L2012 LCD Module - datasheet-3.pdf) which can be driven straight from the Arduino example library. I modified a Xino to directly drive one with a 14-pin header soldered to the prototype area of the board. This module I rescued from the skip at work and it has some damage to the LCD but it is entirely usable.

Voice

I need a device that can play back my recordings on demand. Some sort of controllable MP3 player would be ideal. How do I make an MP3 player controllable? Wire into the buttons? Possible. I'd need some feedback on what's playing or whatever is useful or available. I could try to read the LCD screen! I could try to "listen" to the audio output!

I need speakers!

An MP3 shield is a fine solution but it's not my cup of tea: too easy and no pain! I could make my own MP3 shield: -

Other devices can play audio and MP3s: PDAs, phones, etc. Can they be driven?

Voice Update - espeak

Advantages: -

  • the original comedy sketch has limited phrases that can be tough to extract cleanly. With text-to-speech, cheesoid can now say virtually anything
  • I can develop the voice using the espeak config
name english_cheesoid
language en-uk-chs
language en-uk  4
language en 5
gender male

pitch 125 135

flutter 8
echo 100 30
roughness 4
voicing 150


;phonemes en-wm

;replace 00 h NULL
;replace 00 o@ O@
;replace 00 i@3 i@
;dictrules 6

intonation 3
;stressAdd 0 0 0 0 0 0 0 20


;comment?

--Michael Erskine 09:44, 14 September 2011 (EST)

Sense of Smell

Wow! I've located a sensor that might actually be able to detect cheese and petrol!

http://www.figarosensor.com/products/2602pdf.pdf

A small case fan at the body end of the nose hose should be fine to draw air over the sensor. This would have to sit nicely with the nose movement stepper motor.

Movement and Power

Although I eventually want the robot to be pretty autonomous, initially I guess any kind of movement will be good. I imagine simply mounting the body on a reasonably powerful R/C car or tank. I'm going to have to get to grips with servos and R/C in general. I'll be looking out for tank track parts (e.g. bike chain tracks) in the meantime for a more serious robot movement base.

For power I want to try out using some of the 12v and 6v lead acid batteries from the Emergency Roadside Telephone. I have recharged a 12v one and it seems quite happy after being sat on a shelf for many years! I also have my solar panel and I'd like to make use of it for recharging.

--Michael Erskine 16:38, 3 May 2011 (BST)

More thoughts on movement: there are quite a few parameters when getting hold of motors but where to start? I have 12v batteries so want 12V motors and they need a certain amount of "oomph". My simple cyclist's brain understands that gearing is key to getting what I want and that also some function of wheel size. Whilst I'd love to have tank tracks I'm thinking of starting out with an "arse-dragging" robot: two wheels at chassis centre left and right and a lightly sprung castor each at the front and back for stability. The robot is going to be able to trundle around a nice flat space (the HackSpace or my home) and get over some small bumps.

I've already decided that I want to make the wheels from a stack of old CDs with Sugru tyres. They will therefore be a little over 120mm in diameter. This directs me to consider that a single rotation of the wheel will cover a distance equal to the circumference, or Pi x D = 3.14 x 120mm = 377mm. Nice! It'll be slightly more than that with tyres. This directs me to consider the RPM parameter I need to attain a certain speed: I can start by visualising some easy parameters, so if the robot wants to cover say a meter in a second then to my mind that's a pretty fast robot - I don't think R2D2 could do 1m/sec! What's this in km/hour? Google says: http://www.google.co.uk/search?q=1m%2Fsec+in+km%2Fhr = 3.6 km/hr = 2.24 mph. I like that! OK, how many revolutions of the wheel are there in a meter? 1000/377 =~ 2.65 revs. That's about 2652 revolutions in a km. To go 3.6kph I need 3.6 x 2652 revs (in an hour) =~ 9549 revs (per hour) or 9549 / 60 revs per minute =~ 159 RPM. Is that right?

--Michael Erskine 15:26, 6 September 2011 (EST)

I've established that I want 160RPM 12V motors

The 25mm body motors like these ones... 

   Torque: 60 N*cm
   12V DC
   120RPM
   Diameter: 25mm
   Length (excluding shaft): 59mm
   Shaft length: 11mm
   Total length: 70mm
   Shaft diameter: 4mm
   Weight: 92g

OK, so 4mm shaft and a bit small perhaps. The 60Ncm is the decider I guess

Ooh, this 25mm dia one is 90Ncm...

...but only 100RPM

This one is 37mm body 6mm shaft 120RPM 0.5A...

Here's a $9 160RPM beast!

Same one from another seller (maybe same seller!)...

Hmm, 150RPM 37mm Diameter...

Looks the same as...

OK, I've ordered a pair of 37mm 150RPM gearmotors from China - fingers crossed they're going to be suitable!

--Michael Erskine 9 September 2011 (EST)

A new development: Aug 2011 - give Cheesoid a proper brain with an old eeePC

After some time on the back-burner (Arcade Machine and Barcamp) this project has gained momentum again with the resurrection of my dead Asus eeePC 701. I am now using this little gem as the brains inside Cheesoid which solves a number of issues but perhaps introduces a few too! A quick list: -

  • this is the 701 4g version: http://en.wikipedia.org/wiki/Eeepc
  • I bought this eeePC 701 from Andy Beale some time ago and over time the keyboard broke followed by the power port. I tried previously to fix the power port but failed. A redoubled effort got it going yesterday but I don't know about the battery life!
  • an external USB keyboard is enough to get things going
  • it's a Linux box with bash and a full Java JVM!!!
  • it can play WAV and MP3 files with mplayer - solving my voice issues
  • there is a voice recognition app!
  • it has WiFi!
  • it can power the Arduino and also talk to it over the USB-Serial
  • I think I'll develop on my Arduino Uno - maybe even running the IDE on the eeePC
  • The eeePC just about fits into the cylindrical body of Cheesoid apart from cables plugged into the side ports. I have modified a USB extension cable to have a tight bend after the plug and it seems to work OK
  • The dimensions of the eeePC 701 4G: 225mm wide, 165mm deep, ~25mm hight when closed

PC application and Arduino sketch

Now the eeePC is to be used I want to use one of my genuine Arduino boards for the USB serial. I'd prefer not to use the UNO as it seems to have more issues with the USB/Serial but I need to retain my Duemilanove for most prototyping. Perhaps it's time to start making PaperFTDI cables (http://txapuzas.blogspot.com/2010/07/cable-de-programacion-para-arduino-ftdi.html) so I can use the Xino boards.

OK, so since my eeePC has a full Java VM perhaps I might write the PC end in Java. I wouldn't really host an IDE on the eeePC though so perhaps Perl is better option for quick prototyping. I don't think I need bother too much with Dev::Serial (or whatever it's called nowadays) since under Linux I can use tty to set up the port and just open the device as a plain filehandle. Good in theory! I'll have a go with this later. Update Sept 2011: Dev::Serial won't easily build on the eeePC so I've knocked Perl on the head for the main app and I'm going with Java.

On the Arduino end I'll probably keep the LCD panel running from the modified Xino and maybe talk to it with softserial from the other Arduino or talk to it from the PC app - wow, the possibilities! Either way I'll be wanting to chop the loop functionality into blocks and perhaps implement a cheap scheduler.

  • Switch debounce for all inputs
  • LED eye flash routines - for different modes
  • nose control
  • PIR or sonar detection for proximity of smell sample!
  • mode change detection

test sketch

Using a simple counter for scheduling tasks that repeat at different rates. Serial input just echoes right now. 

// Two LEDs are used for eyes on two digital pins...
const int redeye = 5;
const int greeneye = 6;
// The mode switch is on a digital input...
const int switchpin = 7;

// main loop has 10ms sleeps...
const int naptime = 10;
// the eyes flash every 60 loops = 600ms...
int eyefreq = 60;
// info is sent out on the serial port every 100 loops = 1s...
int reportfreq = 100;
// the mode switch is read every 10 loops = 100ms...
// TODO - using an experimental debounce instead
//int switchreadfreq = 10;
// a simple loop counter is used to decide what to do...
unsigned int loopcounter = 0;

int mode = 0;

void setup() {
    Serial.begin(9600);
    pinMode(greeneye, OUTPUT);
    pinMode(redeye, OUTPUT);
    pinMode(switchpin, INPUT);
    // announce startup...
    flasheyes();
    Serial.println("\n=== CHEESOID ===");
    // TODO: piezo buzzer to play a tune
    mode = digitalRead(switchpin);
}

void flasheyes() {
    for(int i=0;i<6;i++){
        int onoff = i % 2;
        digitalWrite(greeneye, onoff);
        digitalWrite(redeye, onoff);
        delay(200);
    }
}

void loop() {
    do_switch();
    do_eyes();
    do_report();
    do_serialinput();
    delay(naptime);
    loopcounter++;
}

void do_switch() {
    // button debounce: state must remain stable for N samples.
    // This is just a lightweight debouncer
    // used if we want to avoid the more general purpose 
    // but heavyweight Bounce library.
    
    const int debouncesamples = 5;
    static int lastsample = 0;
    static int steadycount = 0;
    static int debounced = 0;
    // if the value is steady for 
    int sample = digitalRead(switchpin);
    // a change of value - restart the steady count...
    if(sample != lastsample){
        lastsample = sample;
        steadycount = 0;
        return;
    }
    steadycount++;
    if(steadycount < debouncesamples)
        return;
    steadycount = debouncesamples;
    debounced = sample;
    // set the actual mode switch value
    mode = debounced;
}

void do_eyes() {
    static int eyestate = 0;
    if(loopcounter % eyefreq != 0)
        return;
    eyestate = !eyestate;
    digitalWrite(greeneye, eyestate);
    digitalWrite(redeye, !eyestate);
}

void do_report() {
    if(loopcounter % reportfreq != 0)
        return;

    Serial.print("CHEESOID: mode = ");
    Serial.print(mode);
    //~ Serial.print(" | eye = ");
    //~ Serial.print(onoff);
    Serial.print(" | loop = ");
    Serial.println(loopcounter);
}
void do_serialinput() {
    // can we avoid buffer overflows when using the 
    // standard serial library at a 10ms read rate at 9600 baud?
    // Well, 9600 8-n-1 is 960 bytes per sec or 9.6 per 10ms
    // The standard serial receive buffer holds 128 bytes so we're fine

    static int maxread = 0;
    // any data waiting?
    int len = Serial.available();
    if(!len)
        return;
    if(len > maxread)
        maxread = len;
    for(int i = 0; i < len; i++){
        int c = Serial.read();
        Serial.println(c); // just echo for testing
    }
}

eeePC spares: keyboard and original PSU

Many thanks to Dr Matt Little for donating his broken black eeePC 701 in the HackSpace donation box. (I was unable to get it running as a machine in its own right - something wrong with the onboard flash?)

  • this has made quite a difference!
  • The cheesoid eeePC now has a nice replacement keyboard in contrasting black
  • This means I don't need the external USB keyboard
  • there are other spares available if things get broke (and I'm able to fix them!)
  • I'm now interested in mounting an external webcam!

eeePC mounting and housing

Original plan: have the eeePC fully inside the cylinder

    • poor access to the ports on the side :(
    • awkward for disassembly

New plan: the eeePC will be mounted in a simple "pizza box" shaped housing underneath the cylinder and on top of the chassis.

  • pizzabox is custom fit with port access and hopefully better airflow
  • using 6mm "foam sandwich" display boards for the outer material
  • the cylinder is to sit on top with locating pegs or similar
  • still need the eeePC to be open - how can I get it to stay awake when the lid is closed?
    • eeePC forums
  • ports: -
    • VGA
    • audio (headphone only)
    • USB keyboard & mouse
    • USB for Arduinos
    • other? webcam?
  • now rethinking the steel chassis which is ready formed into a nice shape and decorated but heavy and restrictive to work around

eeePC software

The eeePC run the main Java application as a Poor Man's Service under screen. This app communicates over serial USB to the Arduino UNO.

  • I already shoehorned a full Sun JRE onto the eeePC (for CAL Cube Timer!)
  • using the RXTX java serial API - I'm very familiar with it
  • main class is com.tecspy.cheesoid.CheesoidControl
  • just a console app - no GUI - runs under screen
    • can SSH into the box over the wireless
      • I installed ssh-server
      • need a passworded account ("user" on eeePC has no password and I don't want to open it to the world!)
      • will no longer need to open the case to configure and test
  • main loop reads from standard input for direct commands
Retrieved from "https://wiki.nottinghack.org.uk/index.php?title=Cheesoid&oldid=2056"