SE-CNC-1: Difference between revisions
update |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 8: | Line 8: | ||
|team= | |team= | ||
|induction=[[/Inductions|Planned]] | |induction=[[/Inductions|Planned]] | ||
|defunct= | |defunct=yes | ||
|defunctdate= | |defunctdate=13-12-2019 | ||
}} | }} | ||
{{Archive|date=December 2019}} | |||
{{note|The CNC machine was removed from the space in December 2019 as Alex has sold it.}} | |||
This is a large 3 Axis CNC Mill owned by a Member that was offered as a Long Term Loan to the space. Following a discussion at the [[2019-03-06_Agenda|2019-03-06 Members Meeting]], it was agreed that the donation would be accepted and the tool would be brought in for the enclosure to be built. | This is a large 3 Axis CNC Mill owned by a Member that was offered as a Long Term Loan to the space. Following a discussion at the [[2019-03-06_Agenda|2019-03-06 Members Meeting]], it was agreed that the donation would be accepted and the tool would be brought in for the enclosure to be built. | ||
| Line 92: | Line 96: | ||
==See Also== | ==See Also== | ||
https://sklv.me/post/secnc1.html | https://sklv.me/post/secnc1.html | ||
[[Category:Computer aided manufacture]] | |||
Latest revision as of 17:00, 30 December 2019
| SE-CNC-1 (defunct) | |
|---|---|
 | |
| Manufacturer | Custom Built |
| Model | SE-CNC-1 |
| Obtained | Long term loan (17-03-2019) |
| Team | Tools |
| Induction Required | Planned |
| Status | Defunct (13-12-2019) |
| Tools: all pages • list • Power Tools • Broken tools {{}} | |
 |
The information on this page is NOT current. It retained for historical or archival purposes only. (December 2019) |
Note: The CNC machine was removed from the space in December 2019 as Alex has sold it.This is a large 3 Axis CNC Mill owned by a Member that was offered as a Long Term Loan to the space. Following a discussion at the 2019-03-06 Members Meeting, it was agreed that the donation would be accepted and the tool would be brought in for the enclosure to be built.
Points to note:
- The Tool will require an induction.
- It will be bookable, but not charged for.
- Anyone using the tool will be expected to bring their own tooling.
- Any additional funds required to build the enclosure must be sourced through a Pledge Drive, not paid for by the space.
- The tool will be located in the Downstairs metalworking area.
Machine Specs
Axes
| Axis | Footprint(mm) | Travel(mm) | Ballscrews | Rails |
|---|---|---|---|---|
| X | 1020 | 500 | 2 * 1610 | 2 * THK SHS25V / 4 blocks / 760mm |
| Y | 1000 | 450/500* | 1 * 1610 | 2 * HIWIN EGW15CAH / 4 blocks / 540mm |
| Z | 1000 | 100 | 1 * 1605 | 2 * THK SR25V / 4 blocks |
Electronics
| Spindle | 80mm / 2.1kW / 24000rpm |
|---|---|
| VFD | Hyunyang HY02D223B 2.2kW |
| Motors | Nema23 3Nm @ 2:1 pulley ratio |
| Motor Drivers | 4 * Leadshine DM860 @ 70V |
| Controller Hardware | Intel D945GCLF2 |
| Controller Software | LinuxCNC |
Commissioning
This section will eventually be split off into a sub-page once the tool is ready to use.
Transport to the Hackspace
The tool was collected from the long term storage in March 2019 following approval being given at the March members meeting. It was dismantled and transported in 2 trips using a Ford Focus to save on the cost of hiring a van.
Whilst the enclosure is constructed, the tool has been stacked up against a wall in the Downstairs Metalworking Area.
-
Frame loaded into the car -
On the pallet truck -
Stacked up in the corner
Building the Enclosure
The enclosure is needed to enable full flood coolant capabilities on the machine. Construction is already underway.
If you are able and would like to get involved in this, please join the #CNC Slack Channel