Warco GH-1330 Lathe: Difference between revisions
DauntlessA (talk | contribs) Removed Manual from Cambridge (due to differences from ours), changed specification section to match our manual. |
DauntlessA (talk | contribs) m Made formatting consistent in 'specification' section. |
||
| Line 68: | Line 68: | ||
|} | |} | ||
Compound and Carriage | Compound and Carriage: | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
| Line 83: | Line 82: | ||
|} | |} | ||
Tailstock | Tailstock: | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
| Line 93: | Line 92: | ||
|} | |} | ||
Miscellaneous | Miscellaneous: | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
Revision as of 00:21, 2 September 2022
| Warco GH-1330 Lathe | |
|---|---|
 | |
| Manufacturer | Warco |
| Model | GH-1330 |
| Obtained | Pledge Drive (17/06.2016) |
| Location | Metalworking Downstairs |
| Team | Metalworking |
| Induction Required | Yes (use request form) |
| Tools: all pages • list • Power Tools • Broken tools {{}} | |
History
Model: https://www.warco.co.uk/metal-lathes/303222-gh1330-lathe.html
Acquired in via the New_Tools_May_2016/Pledge_Drive
Was owned by Paul Hayward of Silkstone whistles
https://web.archive.org/web/20130614185755/http://www.silkstonewhistles.com/
Specification
Capacities:
| Swing Over Bed | 330mm / 13" |
| Swing Over Cross Slide | 198mm / 7 3/4"" |
| Swing Through Gap | 476mm / 18 7/8" |
| Length of Gap | 205mm / 8 1/8" |
| Distance Between Centres | 750mm / 30" |
Headstock:
| Hole Through Spindle | 38mm / 1 1/2" |
| Spindle Nose | D1-4 |
| Taper in Spindle Nose | M.T.5 |
| Spindle Taper Adapter | M.T.3 |
| Number of Spindle Speeds | 8 |
| Range of Spindle Speeds | 70-2000rpm |
Gearbox:
| Number of Metric Threads | 29 |
| Range of Metric Threads | 0.45~7mm |
| Number of Inch Threads | 32 |
| Range of Inch Threads | 3 1/2~80TPI |
| Lead Screw Pitch | 7/8" x 8TPI |
| Feed Rod Diameter | 3/4" |
Compound and Carriage:
| Toolpost Type | 4-Way |
| Maximum Tool Size | 16x16mm / 5/8"x5/8" |
| Maximum Compound Slide Travel | 72mm / 2 7/8" |
| Maximum Cross Slide Travel | 160mm / 6 5/16" |
| Maximum Carriage Travel | 630mm / 25" |
Tailstock:
| Tailstock Spindle Travel | 92mm / 3 3/4" |
| Diameter of Tailstock Spindle | 32mm / 1 1/4" |
| Taper in Tailstock Spindle | M.T.3 |
Miscellaneous:
| Width of Bed | 187mm / 7 3/8" |
| Main Motor | 2HP, 1Ph, 240V |
| Height | 1360mm / 53 1/2" |
| Length | 1645mm / 65" |
| Width | 750mm / 30" |
| Net Weight (approx.) | 460kg / 1013lbs |
| Shipping Weight (approx.) | 560kg / 1235lbs |
The Manual is located by the machine.
Safety
DO NOT OPERATE THE LATHE UNTILL YOU HAVE BEEN INDUCTED.
As always at the Hackspace YOU are responsible for your own safety, proper machine operation and safety of those around you.
Borrowed most of the following from Mini-lathe.com & lathes.co.uk --'RepRap' Matt
- Always wear eye protection
- Wear short sleeve shirts, if possible, or shirts with snugly fitting cuffs if long sleeve
- Loose sleeves can catch on rotating work and quickly pull your hand or arm into harm's way. 'RepRap' Matt has the scar to prove this point!
- Remove wrist watches, necklaces, chains and other jewellery
- Tie back long hair so it can't get caught in the rotating work
- Never, ever, leave a chuck key in a chuck.
- Get in the habit of removing the chuck key immediately after use
- Never remove your hand from the chuck key when it is in the chuck
- Keep your fingers clear of the rotating work and cutting tools
- Avoid reaching over the spinning chuck
- For filing operations, hold the tang end of the file in your left hand so that your hand and arm are not above the spinning chuck
- After setting up any turning job, take a moment to pull the job round by hand to check that everything clears
Operation
Drill & Thread Charts
Refresher Video
This helpful video from Cambridge Makerspace gives an overview of the features on the Warco Lathe. It does not act as a replacement for the induction but is a useful tool for jogging your memory after you've had an induction.